/**
 *
 * HX711 library for Arduino - example file
 * https://github.com/bogde/HX711
 *
 * MIT License
 * (c) 2018 Bogdan Necula
 *
**

#include "HX711.h"


// HX711 circuit wiring
const int LOADCELL_DOUT_PIN = 21;
const int LOADCELL_SCK_PIN = 20;


HX711 scale;

void setup() {
  Serial.begin(38400);
  Serial.println("HX711 Demo");

  Serial.println("Initializing the scale");

  // Initialize library with data output pin, clock input pin and gain factor.
  // Channel selection is made by passing the appropriate gain:
  // - With a gain factor of 64 or 128, channel A is selected
  // - With a gain factor of 32, channel B is selected
  // By omitting the gain factor parameter, the library
  // default "128" (Channel A) is used here.
  scale.begin(LOADCELL_DOUT_PIN, LOADCELL_SCK_PIN);

  Serial.println("Before setting up the scale:");
  Serial.print("read: \t\t");
  Serial.println(scale.read());			// print a raw reading from the ADC

  Serial.print("read average: \t\t");
  Serial.println(scale.read_average(20));  	// print the average of 20 readings from the ADC

  Serial.print("get value: \t\t");
  Serial.println(scale.get_value(5));		// print the average of 5 readings from the ADC minus the tare weight (not set yet)

  Serial.print("get units: \t\t");
  Serial.println(scale.get_units(5), 1);	// print the average of 5 readings from the ADC minus tare weight (not set) divided
						// by the SCALE parameter (not set yet)

  scale.set_scale(1000.f);                      // this value is obtained by calibrating the scale with known weights; see the README for details
  scale.tare();				        // reset the scale to 0

  Serial.println("After setting up the scale:");

  Serial.print("read: \t\t");
  Serial.println(scale.read());                 // print a raw reading from the ADC

  Serial.print("read average: \t\t");
  Serial.println(scale.read_average(20));       // print the average of 20 readings from the ADC

  Serial.print("get value: \t\t");
  Serial.println(scale.get_value(5));		// print the average of 5 readings from the ADC minus the tare weight, set with tare()

  Serial.print("get units: \t\t");
  Serial.println(scale.get_units(5), 1);        // print the average of 5 readings from the ADC minus tare weight, divided
						// by the SCALE parameter set with set_scale

  Serial.println("Readings:");
}

void loop() {
  Serial.print("one reading:\t");
  Serial.print(scale.get_units(), 1);
  Serial.print("\t| average:\t");
  Serial.println(scale.get_units(10), 1);

  scale.power_down();			        // put the ADC in sleep mode
  delay(1000);
  scale.power_up();
}



/* #include <Arduino.h>
#include <HX711.h>
#include <RtcDS3231.h>



int RXLED = 17; // The RX LED has a defined Arduino pin
                // Note: The TX LED was not so lucky, we'll need to use pre-defined
                // macros (TXLED1, TXLED0) to control that.
                // (We could use the same macros for the RX LED too -- RXLED1,
                //  and RXLED0.)

// 1. HX711 circuit wiring
const int LOADCELL_DOUT_PIN = 21;
const int LOADCELL_SCK_PIN = 20;

// 2. Adjustment settings
const long LOADCELL_OFFSET = 50682624;
const long LOADCELL_DIVIDER = 5895655;

HX711 loadcell;

void setup()
{
  pinMode(RXLED, OUTPUT); // Set RX LED as an output
  // TX LED is set as an output behind the scenes

  Serial.begin(9600); //This pipes to the serial monitor
  Serial.println("Initialize Serial Monitor");

  Serial1.begin(9600); //This is the UART, pipes to sensors attached to board
  Serial1.println("Initialize Serial Hardware UART Pins");

  // 3. Initialize library
  loadcell.begin(LOADCELL_DOUT_PIN, LOADCELL_SCK_PIN);
  loadcell.set_scale(LOADCELL_DIVIDER);
  loadcell.set_offset(LOADCELL_OFFSET);
}

void loop()
{
  // Serial.println("Hello world!!!");               // Print "Hello World" to the Serial Monitor
  // Serial1.println("Hello! Can anybody hear me?"); // Print "Hello!" over hardware UART

  // 4. Acquire reading
  Serial.print("Weight: ");
  Serial.println(loadcell.get_units(10), 2);

  digitalWrite(RXLED, LOW); // set the RX LED ON
  TXLED0;                   //TX LED is not tied to a normally controlled pin so a macro is needed, turn LED OFF
  delay(200);               // wait for a second

  digitalWrite(RXLED, HIGH); // set the RX LED OFF
  TXLED1;                    //TX LED macro to turn LED ON
  delay(200);                // wait for a second
} */